Care & Cleaning

For best results, keep the following in mind when caring for your KOHLER^® product:

Always test your cleaning solution on an inconspicuous area before applying to the entire surface.
Wipe surfaces clean and rinse completely with water immediately after applying cleaner. Rinse and dry any overspray that lands on nearby surfaces.
Do not allow cleaner to soak.
Use a soft, dampened sponge or cloth. Never use an abrasive material such as a brush or scouring pad to clean surfaces.
Click here for warranty information.

* Success with cleaners and procedures is dependent upon such factors as the hardness and temperature of the water, using exact measurements of ingredients, changes in cleaning formulas and the condition of the product being cleaned. Since there are variations within these factors, Kohler cannot guarantee the effectiveness of the formulas.

Baths & Whirlpools

Vitreous China Faucets and Finishes

Rinse thoroughly and use a soft cloth to wipe the product dry after each use.
In the rare occurrence of stubborn stains, use abrasive cleaners sparingly.
Use a soft nylon brush on the Safeguard surface, on the bottom of the bath.
Do not use steel wool, wire brushes or abrasive sponge pads.
Learn how to flush your whirlpool.

Cleaning instructions listed pertain only to their corresponding material, and are not intended for faucet cleaning. Faucet cleaning instructions for chrome and vitreous china.

Success with cleaners and procedures is dependent upon such factors as the hardness and temperature of the water, using exact measurements of ingredients, changes in cleaning formulas and the condition of the product being cleaned. Since there are variations within these factors, Kohler cannot guarantee the effectiveness of the formulas mentioned.

Care Tip

Cream-based cleaners may have a tendency to build up, reducing the friction on slip-resistant surfaces. Be sure to use a water-soluble cleaner (dissolves 100% in water).

Acrylic Baths & Whirlpools

Wipe out bath/whirlpool after each use with soft cloth or squeegee.
Do not use abrasive cleaners.
Avoid using aerosol products on the bath surface.
Learn how to flush your whirlpool.

Cleaning instructions listed pertain only to their corresponding material, and are not intended for faucet cleaning. Faucet cleaning instructions for chrome and vitreous china.

Success with cleaners and procedures is dependent upon such factors as the hardness and temperature of the water, using exact measurements of ingredients, changes in cleaning formulas and the condition of the product being cleaned. Since there are variations within these factors, Kohler cannot guarantee the effectiveness of the formulas mentioned.

Care Tip

To restore dull or scratched units: Apply white automotive polishing compound with a clean cloth. Rub scratches and dull areas vigorously. Wipe off residue. Follow with a coat of white automotive paste wax.

Do not wax areas where you walk or stand. Damaged surfaces can be repaired. Check classified advertising for "Fiberglass-Repair."

Lithocast^® Baths and Whirlpools

Wipe out bath/whirlpool after each use with soft cloth or squeegee.
Do not use abrasive cleaners.
Avoid using aerosol products on the bath surface.
Learn how to flush a KOHLER whirlpool system.

Cleaning instructions listed pertain only to their corresponding material, and are not intended for faucet cleaning. See faucet cleaning instructions for chrome and vitreous china.

Success with cleaners is dependent upon such factors as the hardness and temperature of the water, using exact measurements of ingredients, changes in cleaning formulas and the condition of the product being cleaned. Since there are variations within these factors, Kohler cannot guarantee the effectiveness of the formulas mentioned.

Flushing Your Whirlpool

Special Considerations - Flushing a Whirlpool System

Flush your whirlpool system twice a month or more, depending upon usage.
Adjust the jets fully clockwise so there is no air induction.
Fill the bath with warm water to a level 2" above the highest jets, or leave water in the bath after using.
Add 2 teaspoons of a low-foaming, powder automatic dishwashing detergent and 20 ounces of household bleach (5% to 6% sodium hypochlorite) to the water.
Run the whirlpool for 5 to 10 minutes. Then shut off the whirlpool and drain the water.
If desired, rinse baths surfaces with water.
Clean KOHLER^® cast iron and acrylic bath surfaces as needed with recommended cleaners.